Forum Replies Created
-
Posted in: Allo USB Bundle
-
28. Juni 2020 at 13:17 #49102
Going back to rpi3+ and check later on a release version if the problem has been solved.
Thanks
Udo24. Juni 2020 at 16:56 #49092Hi Mario,
thanks for the fast response.
The settings are:
Soundcard im Squeezelite Setup: sysdefault – snd_rpi_hifiberry_dacplus
max2Play Version 2.52 for RPI4B 4GB
BT Settings: sndrpihifiberry – hw:1:0 – Mixer Digital – Hifiberry DAC+ proSorry, i did not really understand the dependecies of the several audio out options and the possible signal paths.
22. Juni 2020 at 18:48 #49064I just migrated from RPI3B+ to RPI4 with the new image for model 4.
Everything works using the player with my DAC+ pro card.Unfortunately using the BT speaker function to connect the smartphone does not produce any sound.
The BT link seems to be established/connected, max2play is selected as the media output device, the transport of the music player advances but produces no sound.
Is this issue known in any form for the new max2play image?
Thanks – Udo
15. September 2017 at 16:57 #31347Hi Heiner,
i would appreciate if thing would work like they are intended to…
In fact the outputs are scrambled. The is only gmrenderer active, DAC+ selected, but the standard output is still selected.
DLNA can be used, but only with the RP audio jack.A complete fresh installation (2.44) has the same problem.
Using the command line „speaker-test -Ddefault:sndrpihifiberry -twav“ activates RCA plugs of DAC+ as expected.
-> HW ok.So the front seems to show what should be but not what really is.
-> Test button makes sense.Now i am going to configure the system via text editor, even if thats what i tried to ommit and why i was willing to pay for a simple functioning solution.
Any helpful hints?
Thanks – Udo
15. September 2017 at 12:56 #31345Hi Grisha,
thanks for replying.
I used the thread title because it described my existing problem and the are so many similar threads in this forum.
It seems to be a configuration problem in my case because a can use the DAC+ from the command line.
Thanks & good luck – Udo
15. September 2017 at 12:47 #31343cmdline „speaker-test -Ddefault:sndrpihifiberry -twav“
works fine. No Hardware issue.
So what about gmrenderer? Seems as if she is not willing to use what i told her..
Thanks – Udo
15. September 2017 at 12:33 #31342Hi,-
i have a similar problem: With only gmrenderer active (no player started) i didn’t manage to switch from RP3 output to the installed DAC+.
All settings point to the DAC+ on the WEB surface.Here the „debug output“:
#### SQUEEZELITE VERSION ####
Squeezelite Max2Play v1.0.1 based on v1.8.4-726, Copyright 2012-2015 Adrian Smith, 2015-2016 Ralph Irving.#### SQUEEZELITE BUILDOPTIONS ####
Build options: LINUX ALSA EVENTFD RESAMPLE FFMPEG VISEXPORT IR GPIO DSD CONTROLSBS ALSASYNC BLUETOOTHSYNC#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o sysdefault:CARD=sndrpihifiberry -a 80:4::
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d default:CARD=sndrpihifiberry
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi
YMPD_PARAMETER=–webport 8081
GMEDIARENDER_ALSA_DEVICE=hw:CARD=sndrpihifiberry,DEV=0#### SQUEEZELITE -l ####
Output devices:
null – Discard all samples (playback) or generate zero samples (capture)
equal
plugequal – Equalizer for plughw:0,0
default:CARD=ALSA – bcm2835 ALSA, bcm2835 ALSA – Default Audio Device
sysdefault:CARD=ALSA – bcm2835 ALSA, bcm2835 ALSA – Default Audio Device
dmix:CARD=ALSA,DEV=0 – bcm2835 ALSA, bcm2835 ALSA – Direct sample mixing device
dmix:CARD=ALSA,DEV=1 – bcm2835 ALSA, bcm2835 IEC958/HDMI – Direct sample mixing device
dsnoop:CARD=ALSA,DEV=0 – bcm2835 ALSA, bcm2835 ALSA – Direct sample snooping device
dsnoop:CARD=ALSA,DEV=1 – bcm2835 ALSA, bcm2835 IEC958/HDMI – Direct sample snooping device
hw:CARD=ALSA,DEV=0 – bcm2835 ALSA, bcm2835 ALSA – Direct hardware device without any conversions
hw:CARD=ALSA,DEV=1 – bcm2835 ALSA, bcm2835 IEC958/HDMI – Direct hardware device without any conversions
plughw:CARD=ALSA,DEV=0 – bcm2835 ALSA, bcm2835 ALSA – Hardware device with all software conversions
plughw:CARD=ALSA,DEV=1 – bcm2835 ALSA, bcm2835 IEC958/HDMI – Hardware device with all software conversions
default:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, – Default Audio Device
sysdefault:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, – Default Audio Device
dmix:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct sample mixing device
dsnoop:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct sample snooping device
hw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct hardware device without any conversions
plughw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Hardware device with all software conversions#### SHAIRPORT VERSION ####
2.8.0-openssl-Avahi-ALSA-soxr#### OUTPUT SOUND DETAILS CARD 0 ####
access: MMAP_INTERLEAVED
format: S16_LE
subformat: STD
channels: 2
rate: 44100 (44100/1)
period_size: 440
buffer_size: 8820#### OUTPUT SOUND DETAILS CARD 1 ####
closedThanks – Udo
-