Forum Replies Created
-
Posted in: Allo USB Bundle
-
4. April 2020 at 10:52 #48406
Hi duval,
I had the same issue wuth my installation. Update or config changes were fine, but after reboot everything was lost. This was due to a broken SD card. The only solution is to replace the card.
Thomas
29. Mai 2017 at 15:20 #29100Hi Mohammad,
thank you for the replacement. The volume control is working now!
Only issue I still have is the mute function. Starting the player with -X 22 and when pressing the mute button, the sound is off and can’t be activated again 🙁
Device restart is needed.Best regards
TOM18. Mai 2017 at 16:57 #28930Hi Mohammad,
I agree. Can you please send me a new encoder?
Please find my order number from the Max2Play web shop as a reference:
#2000004063Best regards
TOM17. Mai 2017 at 21:09 #28889Hi Mohammad,
thank’s for coming back. Device is running and volume is controlled by iPeng only. When using the encoder nothing will happen. Mute is working for the time the switch is pushed.
The software for the encoder is installed and process for IQ_rot is running.Best regards
TOM15. Mai 2017 at 13:17 #28847Hi Mohammad,
green cable is connected to GPIO 25 (pin 4) now. The volume control is still not working 🙁 As GPIO25 is used for IR control, it doesn’t make sense to connect the switch between pin 2 and pin 4. But anyhow, let’s concentrate on the encoder and volume control. Do you agree the HW setting is ok? If yes, we should take a look on the software settings.
Here is the current configuration:
#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o sysdefault:CARD=IQaudIODAC -a 80:4:: -o hw:CARD=IQaudIODAC -V Digital -Q
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d default:CARD=IQaudIODAC
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi
YMPD_PARAMETER=–webport 8081
LMSIP=192.168.178.41Best regards
TOM14. Mai 2017 at 23:39 #28838Hi Mohammad,
thank you for your answer. But strange, because that’s exactly what I’ve done. Pin1(GPIO23) from P6 connector, which is the nearest to the chip, is connected to the left pin of the decoder(orange cable on my picture). Pin3(GPIO24) is connected to the right pin of the encoder(brown) and the mid pin of the encoder goes to pin8(0 V) via red cable. Sorry, but I don’t get what’s wrong…
Best regards
TOM9. Mai 2017 at 20:47 #28769Hi Mohammad,
here is a picture, hope it helps:
All connected to P6 on the audio board
Volume:
Pin 1 – orange -> Encoder left
Pin 3 – brown -> Encoder right
Pin 8 – red (0V) -> Encoder midMute:
Pin 2 – yellow
Pin 10- green (0V)Best regards
TOM8. Mai 2017 at 19:13 #28757Hi Mohammad
Yes, I followed http://www.iqaudio.com/downloads/IQaudIO.pdf to connect the encoder. Mute is working so far
I also installed the Rotary plugin but the encoder is not working.Settings for Squeezelite are:
Soundcard: sysdefault
ALSA Parameter: 80:4::
CMD line options: -o hw:CARD=IQaudIODAC -V Digital -QAfter squeezelite restart the logfile shows:
#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o sysdefault:CARD=IQaudIODAC -a 80:4:: -o hw:CARD=IQaudIODAC -V Digital -Q
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d default:CARD=IQaudIODAC
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi
YMPD_PARAMETER=–webport 8081
LMSIP=192.168.178.41Can the -o option be used twice in the parameter setting as this is a combination from sondcard- and cmd line options?
Best regards
TOM -