Robert

Forum Replies Created

Viewing 7 posts - 1 through 7 (of 7 total)
  • Back to forum
    Posted in: Allo USB Bundle
  • Robert premium
    8. Juni 2018 at 20:50 #36124

    Follow-up :

    I received the new i-sabre v4 and everyhting is working great. The problem was a faulty card.

    Robert premium
    3. Juni 2018 at 15:20 #36036

    Seems that the i-sabre V4 I had was the culprit. It went back to Audiosonics and they said that they found the fault in the card. They’ll send a new one and I hope it will work as it should.

    Robert premium
    3. Juni 2018 at 15:18 #36035

    Sorry, I don’t speak German. It is normal to have 2 IPs as you have 2 LAN connections: one via WiFi and one via RJ45 cable. Both should work OK.

    Robert premium
    1. Juni 2018 at 9:48 #36004

    Hi

    The one they propose with their DIY kit, 6v 3A. I haven’y tested the power supply yet and will have a look at it this WE. Thanks for the idea, I had not thought of the power supply as a possible cause…

    Robert premium
    31. Mai 2018 at 14:44 #35996

    Funny, I can’t see my message in the forum but I can see it with a direct link to it… Just a test to see if my message will appear if I answer my message…

    Robert premium
    26. Mai 2018 at 8:35 #35895

    It seems that my message disappeared (or I did an error while correcting the title of the message)

    I had a RPiB and HiFiBerry DAC+ working great under M2P. As usual (!) I didn’t listen to my basics (do not change if it is working…) and decided to upgrade…

    I have bought a Raspberry Pi 3 B+ and a Audiophonics i-sabre V4 (not a typo, it is the V4 and not the V3) and I can’t get any sound out of it 🙁 Audiophonics say that V4 is the same as the V3 with minor position changes for the contacts but it can’t be only that (or my board is half dead).

    I tried my „old“ HiFiBerry DAC+ on the new RPi3B+ and it is working under M2P and Volumio.
    I tried the i-sabre V4 on the RPiB+ under M2P with the Audiophonics V3 plugin and no sound. With HiFiBerry DAC driver no sound either. I tried different settings in the audio player page to no go. It is not possible to use the M2P as a DLNA renderer either. foobar2000 sees the player, starts „playing“ and 1 sec later, the cursor stops. No sound ever came out of the speakers.

    The power button and LED is working.

    I did the tests under Volumio too with the same results : no sound. It thinks that it is playing but as usual, no music from the loudspeakers (yes, I tested the cable and my HiFi system and they are working 😉 ). Again, I played around and tried all the options (those indicated for V3) to no go.

    Any ideas and help would be greatly appreciated.

    Rob

    Robert premium
    2. Januar 2016 at 16:26 #17533

    Hi

    The easiest way (the first 4 steps are done only once 😉 )

    1/ Install foobar2000 on your PC / laptop.
    2/ Install the UPNP MediaRendererOutPut plugin to foobar2000.
    3/ Activate DLNA audio client in Max2Play
    4/ In foobar2000, select the output device max2play-DLNA
    5/ Insert CD in the PC / laptop and play it with foobar2000 with a cristal sound quality 🙂

    I know that is not exactly what you were trying to do but it is easy and works great 🙂

    • This reply was modified 8 years, 11 months ago by Robert.
Viewing 7 posts - 1 through 7 (of 7 total)