Forum Replies Created
-
Posted in: Allo USB Bundle
-
28. November 2015 at 15:14 #17057
So, habe eine Lösung gefunden:
Max2play auf dem Pi2 installiert, dann unter dem Reiter „Raspberry Einstellungen“ unter „Wähle Soundkarte, die beim Start geladen werden soll“ als Soundcard folgendes eingestellt: USB Soundcards (Northstar Essensio, Hiface and others)
Dann Multisqueeze als Plugin installiert, dort unter „Status instance“ und „Erweiterte Optionen“ die Soundkarte „default – USB Audio DAC, USB audio“ eingestellt, bei der zweiten Instance das Gleiche mit Card=DAC_1 am Ende.
Reboot. Fertig.Jetzt laufen auf dem Pi2 gleichzeitig 2 separate Player über zwei recht günstige USB DAC pcm2704 in ansprechender Qualität.
REL
PS: Einen 3. USB-Port habe ich ja auf dem Pi noch frei (2xDAC, 1xUSB-Stick mit MP3), ich werde also noch einen USB DAC anschließen und eine 3. Instanz ausprobieren.
28. November 2015 at 14:37 #17056Hallo Maximilian,
die Sache lässt mir keine Ruhe. Ich habe den Pi samt des USB DAC pcm2704 vorher ohne Probleme mit squeezeplug genutzt, da konnte man den DAC auswählen. Das Gleiche sollte jetzt natürlich auch mit Max2Play klappen.
Ziel ist es, an einem Pi2 3-4 solcher USB-Dac anzuschließen und darauf über Multisqueeze mehrere Player zu simulieren.Habe jetzt alles auf einem Pi2 installiert, den USB DAC pcm2704 angesteckt und bekomme folgende Ausgabe bei dmesg:
[ 0.052577] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[ 0.052617] [bcm2709_smp_prepare_cpus] enter
[ 0.052771] Setting up static identity map for 0x528478 – 0x5284ac
[ 0.112420] [bcm2709_boot_secondary] cpu:1 started (0) 17
[ 0.112726] CPU1: Booted secondary processor
[ 0.112734] [bcm2709_secondary_init] enter cpu:1
[ 0.112788] CPU1: update cpu_capacity 1024
[ 0.112797] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[ 0.132389] [bcm2709_boot_secondary] cpu:2 started (0) 18
[ 0.132649] CPU2: Booted secondary processor
[ 0.132657] [bcm2709_secondary_init] enter cpu:2
[ 0.132689] CPU2: update cpu_capacity 1024
[ 0.132697] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[ 0.152468] [bcm2709_boot_secondary] cpu:3 started (0) 17
[ 0.152706] CPU3: Booted secondary processor
[ 0.152714] [bcm2709_secondary_init] enter cpu:3
[ 0.152742] CPU3: update cpu_capacity 1024
[ 0.152751] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[ 0.152845] Brought up 4 CPUs
[ 0.152965] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.152999] CPU: All CPU(s) started in SVC mode.
[ 0.154005] devtmpfs: initialized
[ 0.178770] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.180750] pinctrl core: initialized pinctrl subsystem
[ 0.183864] NET: Registered protocol family 16
[ 0.189490] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.190649] bcm2709.uart_clock = 3000000
[ 0.193413] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.193466] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.193521] mailbox: Broadcom VideoCore Mailbox driver
[ 0.193653] bcm2708_vcio: mailbox at f300b880
[ 0.194017] bcm_power: Broadcom power driver
[ 0.194053] bcm_power_open() -> 0
[ 0.194079] bcm_power_request(0, 8)
[ 0.694756] bcm_mailbox_read -> 00000080, 0
[ 0.694789] bcm_power_request -> 0
[ 0.694933] Serial: AMBA PL011 UART driver
[ 0.695079] dev:f1: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev3
[ 1.203270] console [ttyAMA0] enabled
[ 1.275647] SCSI subsystem initialized
[ 1.279661] usbcore: registered new interface driver usbfs
[ 1.285331] usbcore: registered new interface driver hub
[ 1.290801] usbcore: registered new device driver usb
[ 1.297715] Switched to clocksource arch_sys_counter
[ 1.333362] FS-Cache: Loaded
[ 1.336598] CacheFiles: Loaded
[ 1.351133] NET: Registered protocol family 2
[ 1.356788] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.364044] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.370745] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.377214] TCP: reno registered
[ 1.380492] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.386479] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.393213] NET: Registered protocol family 1
[ 1.398278] RPC: Registered named UNIX socket transport module.
[ 1.404222] RPC: Registered udp transport module.
[ 1.408995] RPC: Registered tcp transport module.
[ 1.413713] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.421139] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counter s available
[ 1.429552] bcm2708_dma: DMA manager at f3007000
[ 1.434346] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000 000(1008 MiB)
[ 1.444166] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 1.450693] audit: initializing netlink subsys (disabled)
[ 1.456162] audit: type=2000 audit(1.239:1): initialized
[ 1.477765] VFS: Disk quotas dquot_6.5.2
[ 1.482081] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.491629] FS-Cache: Netfs ’nfs‘ registered for caching
[ 1.498057] NFS: Registering the id_resolver key type
[ 1.503186] Key type id_resolver registered
[ 1.507380] Key type id_legacy registered
[ 1.512580] msgmni has been set to 1726
[ 1.518323] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 52)
[ 1.525950] io scheduler noop registered
[ 1.529930] io scheduler deadline registered (default)
[ 1.535393] io scheduler cfq registered
[ 1.541855] BCM2708FB: allocated DMA memory f6c00000
[ 1.546869] BCM2708FB: allocated DMA channel 0 @ f3007000
[ 1.557924] Console: switching to colour frame buffer device 82×26
[ 1.569880] bcm2708-dmaengine bcm2708-dmaengine: Load BCM2835 DMA engine driv er
[ 1.579191] uart-pl011 dev:f1: no DMA platform data
[ 1.586182] vc-cma: Videocore CMA driver
[ 1.591712] vc-cma: vc_cma_base = 0x00000000
[ 1.597986] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 1.604907] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 1.623807] brd: module loaded
[ 1.634301] loop: module loaded
[ 1.639204] vchiq: vchiq_init_state: slot_zero = 0xb6800000, is_master = 0
[ 1.648385] Loading iSCSI transport class v2.0-870.
[ 1.655716] usbcore: registered new interface driver smsc95xx
[ 1.663078] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.870720] Core Release: 2.80a
[ 1.875340] Setting default values for core params
[ 1.881635] Finished setting default values for core params
[ 2.089105] Using Buffer DMA mode
[ 2.093887] Periodic Transfer Interrupt Enhancement – disabled
[ 2.101264] Multiprocessor Interrupt Enhancement – disabled
[ 2.108393] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 2.114303] Dedicated Tx FIFOs mode
[ 2.119649] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xb6c 14000 dma = 0xf6c14000 len=9024
[ 2.132599] FIQ FSM acceleration enabled for :
[ 2.132599] Non-periodic Split Transactions
[ 2.132599] Periodic Split Transactions
[ 2.132599] High-Speed Isochronous Endpoints
[ 2.155532] dwc_otg: Microframe scheduler enabled
[ 2.155604] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x803d98b4
[ 2.163156] WARN::hcd_init_fiq:413: FIQ ASM at 0x803d9c10 length 36
[ 2.171063] WARN::hcd_init_fiq:438: MPHI regs_base at 0xb780a000
[ 2.178673] dwc_otg bcm2708_usb: DWC OTG Controller
[ 2.185155] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 2.194032] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 2.201149] Init: Port Power? op_state=1
[ 2.206606] Init: Power Port (0)
[ 2.211649] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.220054] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 2.228874] usb usb1: Product: DWC OTG Controller
[ 2.235117] usb usb1: Manufacturer: Linux 3.18.11-v7+ dwc_otg_hcd
[ 2.242825] usb usb1: SerialNumber: bcm2708_usb
[ 2.249795] hub 1-0:1.0: USB hub found
[ 2.255113] hub 1-0:1.0: 1 port detected
[ 2.261017] dwc_otg: FIQ enabled
[ 2.261033] dwc_otg: NAK holdoff enabled
[ 2.261044] dwc_otg: FIQ split-transaction FSM enabled
[ 2.261082] Module dwc_common_port init
[ 2.261479] usbcore: registered new interface driver usb-storage
[ 2.269304] mousedev: PS/2 mouse device common for all mice
[ 2.276958] bcm2835-cpufreq: min=600000 max=900000
[ 2.283615] sdhci: Secure Digital Host Controller Interface driver
[ 2.291377] sdhci: Copyright(c) Pierre Ossman
[ 2.297469] DMA channels allocated for the MMC driver
[ 2.337758] Load BCM2835 MMC driver
[ 2.344583] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.355836] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.365815] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.373156] usbcore: registered new interface driver usbhid
[ 2.380408] usbhid: USB HID core driver
[ 2.388265] TCP: cubic registered
[ 2.395210] Initializing XFRM netlink socket
[ 2.401134] NET: Registered protocol family 17
[ 2.407926] Key type dns_resolver registered
[ 2.414089] Registering SWP/SWPB emulation handler
[ 2.421271] registered taskstats version 1
[ 2.427120] vc-sm: Videocore shared memory driver
[ 2.433352] [vc_sm_connected_init]: start
[ 2.435172] mmc0: host does not support reading read-only switch, assuming wr ite-enable
[ 2.437321] mmc0: new high speed SDHC card at address d555
[ 2.438027] mmcblk0: mmc0:d555 SU04G 3.79 GiB
[ 2.448960] mmcblk0: p1 p2
[ 2.467474] Indeed it is in host mode hprt0 = 00021501
[ 2.474725] [vc_sm_connected_init]: end – returning 0
[ 2.494809] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null)
[ 2.506184] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.515533] devtmpfs: mounted
[ 2.520830] Freeing unused kernel memory: 384K (80754000 – 807b4000)
[ 2.647900] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.656307] Indeed it is in host mode hprt0 = 00001101
[ 2.858251] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 2.866875] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.877103] hub 1-1:1.0: USB hub found
[ 2.882988] hub 1-1:1.0: 5 ports detected
[ 3.168028] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.288275] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.297373] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber =0
[ 3.310750] smsc95xx v1.0.4
[ 3.372293] smsc95xx 1-1.1:1.0 eth0: register ’smsc95xx‘ at usb-bcm2708_usb-1 .1, smsc95xx USB 2.0 Ethernet, b8:27:eb:60:0a:d0
[ 3.467969] usb 1-1.2: new high-speed USB device number 4 using dwc_otg
[ 3.578738] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5530
[ 3.589628] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber =3
[ 3.599001] usb 1-1.2: Product: Cruzer
[ 3.599012] usb 1-1.2: Manufacturer: SanDisk
[ 3.599028] usb 1-1.2: SerialNumber: 20044324421631E013B0
[ 3.600074] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 3.605071] scsi host0: usb-storage 1-1.2:1.0
[ 3.635407] udevd[177]: starting version 175
[ 3.698004] usb 1-1.4: new full-speed USB device number 5 using dwc_otg
[ 3.827189] usb 1-1.4: New USB device found, idVendor=08bb, idProduct=2704
[ 3.836801] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber =0
[ 3.849924] usb 1-1.4: Product: USB Audio DAC
[ 3.859249] usb 1-1.4: Manufacturer: Burr-Brown from TI
[ 3.874098] input: Burr-Brown from TI USB Audio DAC as /devi ces/platform/bcm2708_usb/usb1/1-1/1-1.4/1-1.4:1.2/0003:08BB:2704.0001/input/inpu t0
[ 3.893321] hid-generic 0003:08BB:2704.0001: input,hidraw0: USB HID v1.00 Dev ice [Burr-Brown from TI USB Audio DAC ] on usb-bcm2708_usb-1.4/i nput2
[ 4.505562] usbcore: registered new interface driver snd-usb-audio
[ 4.599081] scsi 0:0:0:0: Direct-Access SanDisk Cruzer 1.03 PQ : 0 ANSI: 2
[ 4.614092] sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 4.629595] sd 0:0:0:0: [sda] Write Protect is off
[ 4.637073] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 4.639627] sd 0:0:0:0: [sda] No Caching mode page found
[ 4.647158] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 4.666187] sda: sda1
[ 4.675266] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.753972] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.817294] random: nonblocking pool is initialized
[ 5.507912] FAT-fs (sda1): Volume was not properly unmounted. Some data may b e corrupt. Please run fsck.
[ 7.163322] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 7.474560] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 11.931986] smsc95xx 1-1.1:1.0 eth0: hardware isn’t capable of remote wakeup
[ 13.544158] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E 1
[ 17.083338] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:1 02396k SSFS
[ 17.685373] usbcore: registered new interface driver snd-usb-hifaceIch hoffe, es gibt hier eine Lösung…vor allem, weil es bei Squeezeplug ohne Probleme mit diesem DAC funktionierte. Danke.
REL
18. November 2015 at 23:43 #16961Folgende Ausgabe nach „dmesg“:
[ 1.336179] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 1.342447] audit: initializing netlink subsys (disabled)
[ 1.348169] audit: type=2000 audit(1.100:1): initialized
[ 1.369028] VFS: Disk quotas dquot_6.5.2
[ 1.373545] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.383058] FS-Cache: Netfs ’nfs‘ registered for caching
[ 1.390164] NFS: Registering the id_resolver key type
[ 1.395480] Key type id_resolver registered
[ 1.399696] Key type id_legacy registered
[ 1.405211] msgmni has been set to 742
[ 1.411453] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 52)
[ 1.419470] io scheduler noop registered
[ 1.423616] io scheduler deadline registered (default)
[ 1.429198] io scheduler cfq registered
[ 1.435779] BCM2708FB: allocated DMA memory 57c00000
[ 1.440846] BCM2708FB: allocated DMA channel 0 @ f2007000
[ 1.452222] Console: switching to colour frame buffer device 74×28
[ 1.464603] bcm2708-dmaengine bcm2708-dmaengine: Load BCM2835 DMA engine driv er
[ 1.476005] uart-pl011 dev:f1: no DMA platform data
[ 1.483641] vc-cma: Videocore CMA driver
[ 1.489361] vc-cma: vc_cma_base = 0x00000000
[ 1.495892] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 1.503063] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 1.523848] brd: module loaded
[ 1.535870] loop: module loaded
[ 1.541163] vchiq: vchiq_init_state: slot_zero = 0xd7800000, is_master = 0
[ 1.552377] Loading iSCSI transport class v2.0-870.
[ 1.560739] usbcore: registered new interface driver smsc95xx
[ 1.568516] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.776294] Core Release: 2.80a
[ 1.781131] Setting default values for core params
[ 1.787656] Finished setting default values for core params
[ 1.995089] Using Buffer DMA mode
[ 2.000073] Periodic Transfer Interrupt Enhancement – disabled
[ 2.007623] Multiprocessor Interrupt Enhancement – disabled
[ 2.014930] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 2.020996] Dedicated Tx FIFOs mode
[ 2.026647] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xd7c 14000 dma = 0x57c14000 len=9024
[ 2.039936] FIQ FSM acceleration enabled for :
[ 2.039936] Non-periodic Split Transactions
[ 2.039936] Periodic Split Transactions
[ 2.039936] High-Speed Isochronous Endpoints
[ 2.063264] dwc_otg: Microframe scheduler enabled
[ 2.063373] WARN::hcd_init_fiq:412: FIQ on core 0 at 0xc040116c
[ 2.071073] WARN::hcd_init_fiq:413: FIQ ASM at 0xc0401444 length 36
[ 2.079075] WARN::hcd_init_fiq:438: MPHI regs_base at 0xd8806000
[ 2.086896] dwc_otg bcm2708_usb: DWC OTG Controller
[ 2.093614] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 2.104283] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 2.111540] Init: Port Power? op_state=1
[ 2.117210] Init: Power Port (0)
[ 2.122521] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.132766] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 2.143486] usb usb1: Product: DWC OTG Controller
[ 2.149969] usb usb1: Manufacturer: Linux 3.18.7+ dwc_otg_hcd
[ 2.157531] usb usb1: SerialNumber: bcm2708_usb
[ 2.165054] hub 1-0:1.0: USB hub found
[ 2.170702] hub 1-0:1.0: 1 port detected
[ 2.177092] dwc_otg: FIQ enabled
[ 2.177116] dwc_otg: NAK holdoff enabled
[ 2.177127] dwc_otg: FIQ split-transaction FSM enabled
[ 2.177188] Module dwc_common_port init
[ 2.177763] usbcore: registered new interface driver usb-storage
[ 2.186239] mousedev: PS/2 mouse device common for all mice
[ 2.194692] bcm2835-cpufreq: min=700000 max=700000
[ 2.201692] sdhci: Secure Digital Host Controller Interface driver
[ 2.209845] sdhci: Copyright(c) Pierre Ossman
[ 2.216383] DMA channels allocated for the MMC driver
[ 2.252770] Load BCM2835 MMC driver
[ 2.260327] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.276553] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.284892] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.296792] usbcore: registered new interface driver usbhid
[ 2.306378] usbhid: USB HID core driver
[ 2.314668] TCP: cubic registered
[ 2.321010] Initializing XFRM netlink socket
[ 2.329362] NET: Registered protocol family 17
[ 2.336041] Key type dns_resolver registered
[ 2.343929] registered taskstats version 1
[ 2.350016] vc-sm: Videocore shared memory driver
[ 2.356567] [vc_sm_connected_init]: start
[ 2.363627] [vc_sm_connected_init]: end – returning 0
[ 2.372189] Waiting for root device /dev/mmcblk0p6…
[ 2.379452] Indeed it is in host mode hprt0 = 00021501
[ 2.391056] mmc0: host does not support reading read-only switch, assuming wr ite-enable
[ 2.414987] mmc0: new high speed SDHC card at address 59b4
[ 2.432824] mmcblk0: mmc0:59b4 SDC 14.7 GiB
[ 2.446085] mmcblk0: p1 p2 < p5 p6 > p3
[ 2.512008] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. O pts: (null)
[ 2.523851] VFS: Mounted root (ext4 filesystem) readonly on device 179:6.
[ 2.546505] devtmpfs: mounted
[ 2.552412] Freeing unused kernel memory: 340K (c07a7000 – c07fc000)
[ 2.593155] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.602643] Indeed it is in host mode hprt0 = 00001101
[ 2.813431] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.824200] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.838025] hub 1-1:1.0: USB hub found
[ 2.845296] hub 1-1:1.0: 3 ports detected
[ 3.133031] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.243359] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.265868] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber =0
[ 3.293092] smsc95xx v1.0.4
[ 3.360039] smsc95xx 1-1.1:1.0 eth0: register ’smsc95xx‘ at usb-bcm2708_usb-1 .1, smsc95xx USB 2.0 Ethernet, b8:27:eb:d5:55:6e
[ 3.473037] usb 1-1.2: new high-speed USB device number 4 using dwc_otg
[ 3.610766] usb 1-1.2: New USB device found, idVendor=058f, idProduct=6387
[ 3.624997] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber =3
[ 3.637987] usb 1-1.2: Product: Mass Storage
[ 3.651911] usb 1-1.2: Manufacturer: Generic
[ 3.662918] usb 1-1.2: SerialNumber: 64D74C71
[ 3.676636] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 3.699816] scsi host0: usb-storage 1-1.2:1.0
[ 4.346871] udevd[162]: starting version 175
[ 4.715348] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ : 0 ANSI: 2
[ 4.745185] sd 0:0:0:0: [sda] 3915776 512-byte logical blocks: (2.00 GB/1.86 GiB)
[ 4.783436] sd 0:0:0:0: [sda] Write Protect is off
[ 4.790341] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 4.812918] sd 0:0:0:0: [sda] No Caching mode page found
[ 4.820303] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 4.856088] sda: sda1
[ 4.876214] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.954087] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.285084] bcm2708_i2c_init_pinmode(1,2)
[ 6.463215] bcm2708_i2c_init_pinmode(1,3)
[ 6.698855] pcm512x 1-004c: Failed to reset device: -5
[ 6.876553] pcm512x: probe of 1-004c failed with error -5
[ 7.094098] bcm2708_i2c 20804000.i2c: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100000)
[ 7.414135] random: nonblocking pool is initialized
[ 7.528766] snd-rpi-iqaudio-dac sound: ASoC: CPU DAI (null) not registered
[ 7.775426] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 7.932242] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 8.125390] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 8.149400] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 8.172997] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 9.433353] FAT-fs (sda1): Volume was not properly unmounted. Some data may b e corrupt. Please run fsck.
[ 13.895207] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 14.371989] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 15.020338] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 15.052945] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 15.091451] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 15.120289] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 15.150998] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 15.179854] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 24.009656] smsc95xx 1-1.1:1.0 eth0: hardware isn’t capable of remote wakeup
[ 25.598433] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E 1
[ 34.206247] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:1 39260k SSFS
[ 1617.333527] usb 1-1.3: new full-speed USB device number 5 using dwc_otg
[ 1617.440579] usb 1-1.3: New USB device found, idVendor=08bb, idProduct=2704
[ 1617.440620] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber =0
[ 1617.440640] usb 1-1.3: Product: USB Audio DAC
[ 1617.440659] usb 1-1.3: Manufacturer: Burr-Brown from TI
[ 1617.457902] input: Burr-Brown from TI USB Audio DAC as /devi ces/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3:1.2/0003:08BB:2704.0001/input/inpu t0
[ 1617.458406] hid-generic 0003:08BB:2704.0001: input,hidraw0: USB HID v1.00 Dev ice [Burr-Brown from TI USB Audio DAC ] on usb-bcm2708_usb-1.3/i nput2
[ 1617.458710] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 1617.458791] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 1617.458915] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 1617.459410] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 1617.459491] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 1617.459538] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 1617.460079] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 1617.460152] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 1617.460200] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 1635.789032] usb 1-1.3: USB disconnect, device number 5
[ 1638.836046] usb 1-1.3: new full-speed USB device number 6 using dwc_otg
[ 1638.943773] usb 1-1.3: New USB device found, idVendor=08bb, idProduct=2704
[ 1638.943815] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber =0
[ 1638.943835] usb 1-1.3: Product: USB Audio DAC
[ 1638.943853] usb 1-1.3: Manufacturer: Burr-Brown from TI
[ 1638.962957] input: Burr-Brown from TI USB Audio DAC as /devi ces/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3:1.2/0003:08BB:2704.0002/input/inpu t1
[ 1638.963987] hid-generic 0003:08BB:2704.0002: input,hidraw0: USB HID v1.00 Dev ice [Burr-Brown from TI USB Audio DAC ] on usb-bcm2708_usb-1.3/i nput2
[ 1638.964297] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 1638.964380] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 1638.964429] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 1638.964707] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 1638.964776] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 1638.964822] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra l
[ 1638.965234] snd-rpi-iqaudio-dac sound: ASoC: CODEC DAI pcm512x-hifi not regis tered
[ 1638.965307] snd-rpi-iqaudio-dac sound: snd_soc_register_card() failed: -517
[ 1638.965351] platform sound: Driver snd-rpi-iqaudio-dac requests probe deferra3. November 2015 at 19:12 #16756Danke, Heiner. Hab ich natürlich probiert, klappt nicht.
Kann man die Treiber irgendwie nachinstallieren? -
