Forum Replies Created
-
Posted in: Allo USB Bundle
-
16. September 2019 at 15:00 #47095
Zunächst möchte ich KEINE Simultanausgabe, sondern Videosignal ausschließlich auf den HDMI-Port des RP.
Wenn Du schreibst, bis RP 3B+ ist eine Simultanausgabe nicht möglich, dann gehe ich davon aus dass eine Simultanausgabe auf DSI UND HDMI beim 4er möglich ist!? Oder werden beim 4er nur die beiden HDMI-Ports angesteuert und das DSI abgeschaltet?
6. September 2019 at 17:31 #47019Hallo Heiner,
der RP ist in einer Anlage verbaut, die einen Touchscreen hat. Auf diesem Touchscreen erfolgte ursprünglich die visuelle Ausgabe, bis zur Umstellung auf HDMI. Nun ist aber der Touchscreen wieder aktiv und auf dem TV erscheint nichts, obwohl der HDMI-Port des RP vom TV erkannt wird.
5. September 2019 at 19:12 #47008Ergänzung:
Die Anzeige „HDMI2“ auf dem TV Gerät ist ein Indiz, dass der Connect zum Raspberry erkannt wird.4. Juni 2019 at 15:59 #45600Hallo Bernhard,
hat bestens geklappt. Nochmals herzliches Dank.Nun bräuchte ich das Gleiche noch einmal für Amazon Music. Mit wem von Kodinerds hast Du zusammnengearbeitet?
Grüße
Christian
3. Juni 2019 at 18:32 #45588Hallo Bernhard,
herzlichen Dank für die schnelle Antwort, werde mein Glück versuchen.
Christian
3. Juni 2019 at 14:17 #45563Hallo Bernhard,
auch ich hätte gerne amazon prime (Video & music) auf meinem M2P. Bisher sind meine Versuche gescheitert, leider habe ich auch keine Zeit ein eigenes Plugin zu schreiben.
Könntest Du bitte verraten, wie Du Amazon in Kodi integriert hast.Herzlichen Dank Dir schon mal im Voraus.
Christian
25. Februar 2019 at 22:28 #44560Hi Heiner,
if I interpret the error correctly, the max2play system / environment expect controller or view files. And these files are missing!?
Is that so?
if yes, please can you tell me, which Controller OR View Files are expected?
Thanks a lot.
Christian
22. Februar 2019 at 14:18 #44544Hi Heiner,
every attempt is acknowledged with exactly the same error message – no changes!
And please tell me, what the pertinent files are?
7. Juli 2018 at 22:22 #36480I have opened a new entry for my problem(s).
The just boom is NOT listed! What is going wrong???
19. Juni 2018 at 20:08 #36262Hi Heiner,
thanks for your support.
All topics you have listed, I have donebefore!
Following situation:
With a fresh flashed image (stretch) the device start with a hint to dhcp (row in start sequence).Further, when all settings are done and a reboot is necessary the RPI crash: The RPI tried to start the network time synchro in an endless loop as descriped in my last post. My only chance is to switch off the device.
When I start the RPI after the crash manuel, at first the RPI reports a sdcard failure (three lines). After this the boot sequence runs normal.BUT: I can’t choose in the Kodi settings my justboom, only hdmi and analogous, although I can see in the max2play web interface at the RPI settings that the justboom is set!!!
In the Kodi/XBMC tab „Autostart“ is set.
If I try to connect to the RPI via putty with the formaly known user and password the access will be denied. In the past it’s was possible!
Slowly I despair!!!!!
18. Juni 2018 at 21:25 #36247Hello support,
despite the new image, a kernel update is offered. Is it necessary to install the kernel update. Without this, a reboot isn’t possible, the RPI crashes!!!
To finish my hifi project, I need urgently answers / support!!!
17. Juni 2018 at 20:46 #36226Hello,
I have flashed the sd card with the newest image (stretch).
Beforehand: I follow the configuration instructions eg. for Kodi from the Justboom page to!
I am sorry to say it, but this image are a little bit buggy: It’s not able to reboot correctly eg. after choosing the audio card. The RPI try to initialize to the network, every 15 seconds without a value (endless loop!!!). A break is only pooible with a switch off of the whole device!
In addition, I can only following entry on the KODI configurations screen for the audio devices: ALSA (without a device to the Justboom card). If I choose that, nothing happens, no sound. The hardware is connected without any failure, it’s aproved many times.
What should I do?
14. Juni 2018 at 20:34 #36199Hi Heiner,
thanks for your answer.
In the past, I have taken the image for the 7″ touch display, because I have one installed and on the max2play sites ja recommended to take this image! Have I done a mistake?Now I habe a request for you: Please can you explain the differences between both versions. I would like to avoid having other problems with the stretch version, eg. with my touch display oder installing other plugins.
Thanks for your understanding in advance.
Christian
12. Juni 2018 at 21:05 #36173Hello Heiner,
Thanks for your answer, but what you suggested is already done before.
Are there possibly other reasons?
Or do I have to reckon with a defect of the Justboom card?
What is likely?4. Juni 2018 at 14:21 #36066Completement: The RPI and the screen have the same power supply (Meanwell rs-25-5)
4. Juni 2018 at 13:07 #36047So I understand your answer correctly:
The pin 2 (5 volts) and pin 4 (GRD) in the section P2 are to connect with the screen?But the screen has a power supply directly from the Mean Well power switching device. Is that not correct or have I to break this power connection and the scrren get his power from the Justboom amp, as described above?
4. Juni 2018 at 12:55 #36046This problem I can solve.
But now there is a new problem:
Immediately when starting / gooting appears the temperature symbol (full red) on the touch display.
In the internet I have read, this indicates a to high voltage. Is this correct?
My technical configuration:
RPI with an own power supply (Mean Well rs-25-5) with an output 5.1 Volt (measured)
Justboom Amp Hat with an own power supply (Mean Well rs-75-25) with an output 17,6 Volt (measured)
RPI & Justboom connection: ribbon cable 2 X 20 pins
Do I have a mistake in the technical configuration?
1. Juni 2018 at 19:23 #36012Hello Heiner,
unfortunately I have to reopen this issue.
After comeback from holiday the same behavior es described first time: in the wurden I can see, bis Fuß boot sequenze start and run, I See several lines which are signed with „Ok“ and than only stripes or a grey screen.
Before our vacation the system start properly.
For me it’s mistery – what is wrong or what I am doing wrong? -
