Bassie

Forum Replies Created

Viewing 6 posts - 1 through 6 (of 6 total)
  • 11. August 2017 at 18:55 #30575

    Hi Heiner,

    Thanks, that worked!

    Just a new question.

    When I start a song via Spotify connect, the song is starting at max sound.
    Is there away to make it start at 10% or something like that?

    Also at the lowest volume in sporify via spotify connect, the sound is to loud.
    Is there away to add more steps in the volume control?
    Or can I start the sound at lower stenght that it is now (in stead of 0-100% to 0-50% from normal)?

    Thanks in advance.

    Bassie

    4. August 2017 at 13:14 #30438

    Hi Heiner,

    I have the following line filled in the command line of squeezelite:

    -C 10 -o hw:1,0

    Because I use an USB soundcard I have to add ‚-o hw:1,0‘ and I ticked ‚use USB DAC‘.
    But do I have to add the same for this plugin?, so it knows that it has to use the USB DAC?

    Bij the connect plugin I have the standard output device selected ‚equal -equel‘.
    Should I need to change this output device?

    Thanks for your help.

    3. August 2017 at 20:41 #30404

    Hi All,

    I tried to use the plugin but when I start a song the service stops.

    I get the error below:

    `INFO:librespot::session: Connecting to AP „gew1-accesspoint-b-f6v1.ap.spotify.com:4070“
    INFO:librespot::session: Authenticated as „username“ !
    INFO:librespot::audio_backend::alsa: Using alsa sink
    INFO:librespot::session: Country: „NL“
    INFO:librespot::player: Loading track „Red Earth & Pouring Rain“
    INFO:librespot::player: Track „Red Earth & Pouring Rain“ loaded
    librespot: pcm_params.c:170: snd1_pcm_hw_param_get_min: Assertion !snd_interval_empty(i)' failed.

    So, does someone knows what the issue is?

    I’m using an USB soundcard and that is working correctly with squeezelite.

    3. August 2017 at 14:03 #30380

    Hi Heiner,

    Ok, I will look into the log files then and try if I can see some issues.

    And yes, I have the latest version.
    I think the access point autostart is already set to off, but will check this tonight.

    Thanks for your help.

    3. August 2017 at 12:50 #30371

    Hi Heiner,

    I already checked this.
    I can see that the PI is connected to my router in the router webinterface and the PI is only connected with a Wifi USB stick and I can connect with the PI, so it is using my router.
    I don’t have any restrictions on my router, so the M2P software should connect to the internet.

    The strange thing is that when I connect an UTP cable there is an internet connection right away (same router).
    So I would think that there is a different setting between the WIFI setting and UTP network settings.

    IS there a log file or something on the PI that I can look into?

    3. August 2017 at 10:35 #30361

    Hi Heiner,

    After connecting via WPS, does the system still tell you that you have no internet connection?
    Yes, it did.
    The strange thing is that yesterday evening when I wanted to change the ‚Fix IP setting‘ I had an internet connection.
    So probably, later on it was getting connected to the internet.

    Then I tried to start the ’spotify connect‘ addon and this one started.
    But when I tried to connect with spotify to the spotify connect ‚max2play‘ (yes it was visible in spotify) it looked like the PI restarted.

    So after that I changed the ‚Fix IP‘ off and restarted the PI.
    But then I again had no internet connection.
    So I can connect via Wifi to the PI, but somehow it can’t connect itself to the internet.

    SO still some questions from my side:

    – is there a way I can force the PI to connect to the internet

Viewing 6 posts - 1 through 6 (of 6 total)