No sound after some time in standby

Max2Play Home › Forums › Max2Play as Squeezebox (Player / Server) › No sound after some time in standby

Viewing 4 posts - 1 through 4 (of 4 total)
  • Back to forum
    Posted in: Max2Play as Squeezebox (Player / Server)
  • StephanM. premium
    30. Juni 2022 at 18:02 #52300

    Hi,
    first of all, my hardware:
    Pi3A+
    Hifiberry Digi+ (koax in use)
    Raspberry Pi 7″ Touch Display
    In use with Max2Play 2.56 mainly as Tunein Radio Player with Squeezelite and LMS. Everything works flawless for hours, except i switch to standby (upper left button) for some amount of time. When i turn it on again, there will be no sound, until i reboot. Restart of Audioplayer does not help. I tested with hifiberry as plughw, hw and default, always the same. No other services are in use e.g. Kodi, MPD and so on.
    Some debug infos

    #### SQUEEZELITE VERSION ####
Squeezelite Max2Play v1.0.3 based on v1.8.7-999, Copyright 2012-2015 Adrian Smith, 2015-2017 Ralph Irving.
 

#### SQUEEZELITE BUILDOPTIONS ####
Build options: LINUX ALSA EVENTFD RESAMPLE FFMPEG VISEXPORT IR GPIO DSD CONTROLSBS ALSASYNC BLUETOOTHSYNC
 

#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o default:CARD=sndrpihifiberry -a 80:4:: -v
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d default:CARD=sndrpihifiberry
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi
YMPD_PARAMETER=--webport 8081
BLUEALSA_PLAY_AUDIOCARD=hw:0,0
 

#### SQUEEZELITE -l ####
Output devices:
  null                           - Discard all samples (playback) or generate zero samples (capture)
  equal                         
  plugequal                      - Equalizer for plughw:0,0
  bluetooth                      - Your Bluetooth device 40:EF:4C:FF:03:22
  default:CARD=sndrpihifiberry   - snd_rpi_hifiberry_digi,  - Default Audio Device
  sysdefault:CARD=sndrpihifiberry - snd_rpi_hifiberry_digi,  - Default Audio Device
  iec958:CARD=sndrpihifiberry,DEV=0 - snd_rpi_hifiberry_digi,  - IEC958 (S/PDIF) Digital Audio Output
  dmix:CARD=sndrpihifiberry,DEV=0 - snd_rpi_hifiberry_digi,  - Direct sample mixing device
  dsnoop:CARD=sndrpihifiberry,DEV=0 - snd_rpi_hifiberry_digi,  - Direct sample snooping device
  hw:CARD=sndrpihifiberry,DEV=0  - snd_rpi_hifiberry_digi,  - Direct hardware device without any conversions
  plughw:CARD=sndrpihifiberry,DEV=0 - snd_rpi_hifiberry_digi,  - Hardware device with all software conversions

 

#### SHAIRPORT (SYNC) VERSION ####
3.1.1-OpenSSL-Avahi-ALSA-soxr-sysconfdir:/usr/local/etc
 

#### OUTPUT SOUND DETAILS CARD 0 ####
access: MMAP_INTERLEAVED
format: S24_LE
subformat: STD
channels: 2
rate: 44100 (44100/1)
period_size: 882
buffer_size: 3528
 

#### OUTPUT SOUND DETAILS CARD 1 ####
    #### BOOT CONFIG TXT ####
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=off
gpu_mem=32
dtoverlay=hifiberry-digi
disable_overscan=1

lcd_rotate=2

    I hope, someone can give me a hint, thanks

    MarioM Moderator
    4. Juli 2022 at 13:26 #52305

    Hi Stephan,

    Do you mean the on/off switch in Jivelite? If so, do you have the RPI display plugin installed?
    Please open the web interface of the Squeezebox server for testing. If you press the button in Jivelite, will the button in the server (upper right corner) also change? Please check whether the player is still recognised in the server web interface after switching the button off and on again.

    StephanM. premium
    4. Juli 2022 at 16:24 #52306

    Hi Mario,
    yes, this on/off button on the upper left corner in Jivelite. And yes, the RPI display plugin is installed.
    The button in Webif changes, when triggered on the display.
    But i could not reproduce this error this time. Probably it’s a matter of time.
    One thing is changed, since i saw this problem: i have the LMS installation on a separate Pi now.
    I will test it again when i have more time.
    Thanks
    Stephan

    MarioM Moderator
    7. Juli 2022 at 11:59 #52310

    The button in Jivelite should only switch off the player. So it shouldn’t matter whether the server is running on the same Pi or on a different one. But if the problem no longer occurs, then maybe this is a workaround.

Viewing 4 posts - 1 through 4 (of 4 total)

You must be logged in to reply to this topic.

Register here