New Install of M2P on Pi 3b+ Neither Squeezelite or Squeezebox Server Start

Max2Play Home Forums Max2Play on Raspberry PI New Install of M2P on Pi 3b+ Neither Squeezelite or Squeezebox Server Start

Viewing 4 posts - 1 through 4 (of 4 total)
  • 14. Februar 2024 at 7:54 #53075

    Hello,

    As stated above, my old install stopped working so attempted to start from scratch. Reformat, Install 2.51 image, Update to 2.58, start install of LMS, tried three different versions, 8.3.1, 8.4.0, 8.4.0 nightly. None launch. All return the „sudo: no tty present and no askpass program specified“ error. Installed Run command. Tried the usermod command posted in the forum. No change. I have three Squeezebox touches so hoping to figure out what is wrong vs. leaving M2P for piCore Player. Any assistance would be appreciated.

    Debug info:
    #### FILESYSTEM ####
    Filesystem 1K-blocks Used Available Use% Mounted on
    /dev/root 15128848 2605332 11879816 18% /
    devtmpfs 412040 0 412040 0% /dev
    tmpfs 445320 0 445320 0% /dev/shm
    tmpfs 445320 19112 426208 5% /run
    tmpfs 5120 0 5120 0% /run/lock
    tmpfs 445320 0 445320 0% /sys/fs/cgroup
    /dev/mmcblk0p1 42136 28148 13989 67% /boot
    tmpfs 89064 8 89056 1% /run/user/1000

    #### LOAD AVERAGE ####
    0.00 0.03 0.43 1/208 8562

    #### KERNEL ####
    Linux max2play 6.6.16-v7+ #1732 SMP Tue Feb 13 13:08:08 GMT 2024 armv7l GNU/Linux

    #### LINUX-VERSION ####
    Distributor ID: Raspbian
    Description: Raspbian GNU/Linux 9.3 (stretch)
    Release: 9.3
    Codename: stretch

    Wifi Lan Debug:

    eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
    inet 10.0.0.129 netmask 255.255.255.0 broadcast 10.0.0.255
    ether b8:27:eb:7e:38:c3 txqueuelen 1000 (Ethernet)
    RX packets 45922 bytes 39606334 (37.7 MiB)
    RX errors 0 dropped 6 overruns 0 frame 0
    TX packets 15457 bytes 1506596 (1.4 MiB)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

    lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
    inet 127.0.0.1 netmask 255.0.0.0
    loop txqueuelen 1000 (Local Loopback)
    RX packets 29 bytes 42969 (41.9 KiB)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 29 bytes 42969 (41.9 KiB)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

    ### WLAN ###

    Squeezebox Debug:

    #### SQUEEZESERVER LOG ####

    #### PERL VERSION ####
    v5.24.1

    #### SQUEEZEBOXSERVER PERL VERSION FOUND ####
    5.24

    2. März 2024 at 20:04 #53095

    It seems like M2P has been abandoned. Not one response in 2 weeks (?).

    I have 5 LMS Radios and A Boombox and have mostly been pleased with the performance of my system under M2P,
    except for when the system experiences a glitch, and then the only solution seems to be to re-image the SD card
    and start over.

    M2P was a saviour back when it first came out, as I don’t even remember the name of the system that kept LMS going
    after Logitech abandoned support, but things were sketchy until M2P put it all under control.

    I think my journey here is over, like you, just now experiencing a failure of the SS to stay up and running
    and my post asking for help has now been labeled as „spam“.

    Thanks for mentioning PiCore, I will have to check that out, I love my music and the LMS system flexibility.

    5. März 2024 at 17:46 #53099

    Yes, I’ve also now switched to PiCore and can listen to music again. 🙂

    There was a little learning curve with getting PiCore up and running but once setup I’ve been very happy.

    RIP M2P

    21. März 2024 at 14:32 #53106

    I have working version 8.4.0 from
    https://lms-community.github.io/lms-server-repository/
    Of course It failed to install version 8.5.0 but after reboot automatically found version 8.4.0 and install it over 8.3.1. I had to make upgrade in order to work with latest Tidal plugin.

Viewing 4 posts - 1 through 4 (of 4 total)

You must be logged in to reply to this topic.

Register here