network and squeezelite issue

[jliggio premium]

jliggio premium

24. März 2018 at 18:53 #34716

I’ve tried to re-boot I can access the unit through my home network, When I try to re-boot from the max2play menu, it tells me I am successfully re-booting, but the unit itself does not re-boot. Instead I have to remove power from the unit, and it re-boots again from that moment.

When I re-boot, the process sticks at the player log-in.

Although I can access the unit from my home network, both wirelessly, and using an ethernet cable, jivelite is not started, and it will not start. Also, the unit will not recognize my wireless netowrk, even when I manually input the network name and password.

I tried updating max2play, and it had no effect.

Here is the de-bug information:

#### FILESYSTEM ####
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 29631300 2405924 25899244 9% /
devtmpfs 437060 0 437060 0% /dev
tmpfs 441392 0 441392 0% /dev/shm
tmpfs 441392 7656 433736 2% /run
tmpfs 5120 4 5116 1% /run/lock
tmpfs 441392 0 441392 0% /sys/fs/cgroup
/dev/mmcblk0p1 61384 21472 39912 35% /boot

#### LOAD AVERAGE ####
0.15 0.06 0.05 1/125 6300

#### KERNEL ####
Linux JeffsRaspberryPiPlayer 4.4.14-v7+ #895 SMP Sun Jun 26 13:59:02 BST 2016 armv7l GNU/Linux

#### LINUX-VERSION ####
Distributor ID: Raspbian
Description: Raspbian GNU/Linux 8.0 (jessie)
Release: 8.0
Codename: jessie

[jliggio premium]

jliggio premium

24. März 2018 at 19:04 #34717

I neglected to provide the de-bug information for squeezelite. I cannot get any de-bug information for jivelite, and when I tried to re-install jivelite I was unsuccessful. Here they are:
#### SQUEEZELITE VERSION ####
Squeezelite Max2Play v1.0.2 based on v1.8.4-726, Copyright 2012-2015 Adrian Smith, 2015-2016 Ralph Irving.

#### SQUEEZELITE BUILDOPTIONS ####
Build options: LINUX ALSA EVENTFD RESAMPLE FFMPEG VISEXPORT IR GPIO DSD CONTROLSBS ALSASYNC BLUETOOTHSYNC

#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o default:CARD=ALSA -a 120::16:
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d default:CARD=ALSA
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi

#### SQUEEZELITE -l ####

#### SHAIRPORT (SYNC) VERSION ####
2.8.0-openssl-Avahi-ALSA-soxr

#### OUTPUT SOUND DETAILS CARD 0 ####
closed

#### OUTPUT SOUND DETAILS CARD 1 ####
closed

Network:

Link encap:Ethernet HWaddr b8:27:eb:f7:ee:f7
inet addr:192.168.1.125 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::716d:d162:b1a4:8f56/64 Scope:Link
inet6 addr: 2600:1702:2f0:4490:c83e:3d0c:f27:599d/64 Scope:Global
inet6 addr: 2600:1702:2f0:4490::36/128 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7066 errors:0 dropped:0 overruns:0 frame:0
TX packets:503 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:528578 (516.1 KiB) TX bytes:153101 (149.5 KiB)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:240 (240.0 B) TX bytes:240 (240.0 B)

wlan0 Link encap:Ethernet HWaddr b8:27:eb:a2:bb:a2
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:1 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:60 (60.0 B) TX bytes:0 (0.0 B)

### WLAN ###

Jivelite:

[Heiner premium]

Heiner premium

26. März 2018 at 16:05 #34747

Hi jliggio,

Please try activating the automatic access point mode in our WiFi/LAN menu, click reboot and remove the ethernet cable from your device. Afterwards (ca. 40 seconds later) a new WiFi network by the name of max2play should appear. Please follow these steps to connect to your wifi network.