Einstellung CPU-Frequenz&GPU

[SimonSays premium]

SimonSays premium

27. Juni 2017 at 18:12 #29738

Hallo, sowohl mit der 2.43 als auch mit der letzten Beta klappen die Raspberry-CPU- und GPU-Einstellungen bei mir nicht. Änderungen bei GPU-Ram werden einfach nicht übernommen, bei CPU-Speed-Dropdown sind keine Einträge. Und das auf zwei unabhängig voneinander aufgesetzten Raspberry (einmal Rasp 3, einmal Zero W).
Kann man da was machen?

[Heiner premium]

Heiner premium

28. Juni 2017 at 15:32 #29751

Hi Simon,

Bitte teile die debug info deiner Geräte nach der Einstellung. So können wir besser nachvollziehen was das Problem sein könnte.

[SimonSays premium]

SimonSays premium

28. Juni 2017 at 15:48 #29754

CPU-Einstellung geht wie gesagt überhaupt nicht.

Raspberry 3

#### BOOT CONFIG TXT ####
# For more options and information see
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default „safe“ mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display’s size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
gpu_mem=128
dtoverlay=hifiberry-dacplus
lcd_rotate=2

Raspberry Zero W

#### BOOT CONFIG TXT ####
# For more options and information see
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default „safe“ mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display’s size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
gpu_mem=128

dtoverlay=justboom-dac

[Heiner premium]

Heiner premium

2. Juli 2017 at 14:01 #29782

Hi Simon,
Danke für die schnelle Antwort. Wir werden uns in der kommenden Woche mit diesem Thema befassen und versuchen deine Problematik an ienem Testgerät zu rekreieren.