Bluetooth-Add-on + Squeezelite-Player automatischer switch möglich?

[Misaal premium]

Misaal premium

17. Dezember 2020 at 17:07 #50496

Hallo
Wie schon im Titel geschrieben, besteht die Möglichkeit, dass beim Abspielen eines Audio vom Iphone via Bluetooth-Verbindung, sich der Squeezelite-Player automatisch ausschaltet? Jetzt muss ich zuerst von Hand der Squeezlite-Player ausschalten, damit das Audio vom Iphone via BT abgespielt wird.

#### SQUEEZELITE VERSION ####
Squeezelite Max2Play v1.0.3 based on v1.8.7-999, Copyright 2012-2015 Adrian Smith, 2015-2017 Ralph Irving.

#### SQUEEZELITE BUILDOPTIONS ####
Build options: LINUX ALSA EVENTFD RESAMPLE FFMPEG VISEXPORT IR GPIO DSD CONTROLSBS ALSASYNC BLUETOOTHSYNC

#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o pulse -a 80:4:: -B
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d pulse
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi
GMEDIARENDERER_ALSA_DEVICE=plug:jack
BLUEALSA_PLAY_AUDIOCARD=hw:0,0
BLUEALSA_PLAY_MIXER=Digital
LMSIP=192.168.5.24

#### SQUEEZELITE -l ####
Output devices:
null – Discard all samples (playback) or generate zero samples (capture)
jack – JACK Audio Connection Kit
pulse – PulseAudio Sound Server
equal
plugequal – Equalizer for plughw:0,0
bluetooth – Your Bluetooth device E4:2B:34:27:75:A1
default:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, HiFiBerry DAC+ HiFi pcm512x-hifi-0 – Default Audio Device
sysdefault:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, HiFiBerry DAC+ HiFi pcm512x-hifi-0 – Default Audio Device
dmix:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, HiFiBerry DAC+ HiFi pcm512x-hifi-0 – Direct sample mixing device
dsnoop:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, HiFiBerry DAC+ HiFi pcm512x-hifi-0 – Direct sample snooping device
hw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, HiFiBerry DAC+ HiFi pcm512x-hifi-0 – Direct hardware device without any conversions
plughw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, HiFiBerry DAC+ HiFi pcm512x-hifi-0 – Hardware device with all software conversions
usbstream:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus – USB Stream Output

#### SHAIRPORT (SYNC) VERSION ####
3.3.1-OpenSSL-Avahi-ALSA-soxr-sysconfdir:/usr/local/etc

#### OUTPUT SOUND DETAILS CARD 0 ####
closed

#### OUTPUT SOUND DETAILS CARD 1 ####

#### Bluetooth Installation ####

#### Bluetooth Dongle ####
hci0: Type: Primary Bus: UART
BD Address: B8:27:EB:6D:D3:04 ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING PSCAN
RX bytes:9699350 acl:18678 sco:0 events:636 errors:0
TX bytes:16792 acl:508 sco:0 commands:251 errors:0

#### DEVICE iMigX ####
spawn /usr/bin/bluetoothctl
Agent registered
[0;94m[bluetooth][0m# info E4:2B:34:27:75:A1
Device E4:2B:34:27:75:A1 (public)
Name: iMigX
Alias: iMigX
Class: 0x007a020c
Icon: phone
Paired: yes
Trusted: no
Blocked: no
Connected: no

#### BLUEALSA RUNNING ####
2

#### BOOT CONFIG TXT ####
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default „safe“ mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display’s size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=off

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d
gpu_mem=128
dtoverlay=hifiberry-dacplus
disable_overscan=1

dtoverlay=i2s-mmap

[MarioM Moderator]

MarioM Moderator

22. Dezember 2020 at 15:32 #50510

Hallo Misaal,

das ist nur mit dem Streamen zum Squeezebox Server möglich. Dort kannst du einstellen, dass BT Streaming automatisch startet, wenn sich ein BT Gerät koppelt. Die entsprechenden Optionen findest du unten in unserem Bluetooth Plugin unter dem Punkt „Stream zum Squeezebox Server“.